Other alternative response methods

Step 1 — Remote study with guided digital material

Alternative and supplementary response methods for shorelines: washing techniques and their water management, and in-situ methods such as tilling and controlled burning.

LESSON 1

Washing techniques

Washing techniques include flushing, low-pressure washing, high-pressure washing and steam blasting. These methods are mainly suited to constructed shores and, under certain conditions, also to rocky, boulder and bedrock shores. Washing methods can also be used on other impermeable shore materials, such as compacted sand beaches and vegetated shores. Washing is a practical and effective option early in an operation, before the oil has had time to weather.

Washing methods must not be used in groundwater areas.

Washing methods used in oil-spill response include: flushing with large volumes of water; low-pressure washing with cold water; low-pressure washing with warm or hot water; high-pressure washing with cold water; high-pressure washing with warm or hot water; and steam washing.

When using washing techniques, wash-water management must be considered. Oil that is released must be directed in a controlled way into booms or protected collection pits, from which it is recovered by other means, such as skimmers or pumping. To separate the oil, wash water can be allowed to settle, passed through an oil separator or sorbent materials, or filtered.

Washing techniques create a risk of oil mist. Oil mist is harmful to the respiratory tract and can cause a life-threatening chemical pneumonitis. Respiratory protection must be worn against oil mist, for example in spills involving diesel, light marine fuels, and light and heavy fuel oil. Bio-based fuels such as biodiesel have sometimes been used as solvents when washing off fossil fuels; biodiesels carry a particularly high risk of chemical pneumonitis.

Oil released by washing must be recovered, otherwise the method causes only harm. The use of washing methods can be broken down into the following stages: protecting the clean area, arranging collection and recovery of wash water, washing, and directing and treating oily wash water. Work begins by preparing the area to be cleaned so that operations do not contaminate the surrounding area and wash water is directed to the desired location. Wash water can be led to a collection pit or trench dug in the shore and lined with protective material, or back into a water body where a collection area has been boomed off. Clean areas are protected from splashes using, for example, tarpaulins and sorbent fabrics or mats. Workers must protect themselves from oily aerosols with respiratory protection.

LESSON 2

Flushing with large volumes of water

Flushing means washing oil away with large volumes of water without pressure. Flushing suits impermeable shore materials and has comparatively minor environmental impact. The method also suits vegetated shores and cleaning oiled vegetation.

Flushing with large volumes of water can be done with a fire hose or a perforated pipe. A pipe with holes of about 0.25–0.5 cm is placed along the shore, parallel to the waterline, above the oiled area. When flushing with a fire hose, no nozzle is used on the hose and the jet is not aimed at the oil; instead, water is allowed to run down over the ground, shore bank or similar surface.

LESSON 3

Low-pressure washing

Low-pressure washing with cold water is an effective and practical technique for most impermeable shore materials, such as bedrock and constructed shores, and also for some permeable materials, such as boulder-field shores. The method's effectiveness declines as oil viscosity increases and as the oil penetrates deeper into the shore material.

Low-pressure washing can also be carried out with warm or hot water. Rescue services have field-portable pressure washers that heat the water themselves. The water is heated to below 30 degrees, and pressure below 2 bar is used when washing. When washing a natural shore, the water jet is not aimed directly at plants or perpendicular to the surface being washed; instead the jet is directed at an oblique angle.

LESSON 4

High-pressure washing

High-pressure washing, and washing with warm or hot water, including steam washing, should be avoided on natural shores, as in addition to oil they may also strip away vegetation and kill all living organisms. These methods can be used, with careful judgement, as targeted spot-washing in areas without vegetation or where the oil has already killed it. However, even removing vegetation killed by oil delays the natural recovery of the environment. High-pressure washing may also emulsify the oil. Hot water and high pressure should be used only on jetties and other constructed surfaces.

LESSON 5

Other methods

A roller and a sand sieve, developed specifically for the purpose, have also been used to recover oil from beach sand. These methods are mainly suited to heavy oils.

In-situ methods, meaning those applied on site, aim to change the properties of the oil or move it to a location where its biodegradation speeds up. In-situ methods include, for example, tilling the ground, adding nutrients, moving sediments, and burning the oil. An advantage of these methods is that they do not create waste requiring transport and final disposal.

LESSON 6

Tilling and sediment relocation

Natural degradation can, where necessary, be accelerated by tilling. In this method, the oiled ground surface is turned over and mixed in place. The technique is also called aeration or soil cultivation. The aim is to break up the oiled ground surface, which often forms a crust, increase the surface area of the oiled soil, and bring oil that has soaked into the ground into contact with oxygen, exposing it to oxidation.

LESSON 7

In-situ burning on the shoreline

Oil that has pooled on the shore or collected in depressions can be burned. Burning is also suitable for disposing of oiled driftwood and shoreline debris. Burning must be carried out in a controlled manner and requires a permit from the environmental authorities. Burning of oiled vegetation can be left until winter, when it causes the least harm. Burning is generally permitted only far from habitation; the safety buffer zone must be at least six kilometres, but preferably more than 10 kilometres.

Review questions

For self-study only. Answers are not recorded.

  1. 1. What is included in washing techniques?

    Select all that apply.

  2. 2. Where can oily wash water released by high-pressure washing be directed?

    Select all that apply.

    Answer key awaiting instructor review.

  3. 3. Which in-situ methods can be used?

    Select all that apply.

  4. 4. Can flushing, low- and high-pressure washing, and steam blasting be used in a groundwater area?

    Answer key awaiting instructor review.

The certificate is issued after both the practical exercise and the final exam.