Cleaning of contaminated areas

Step 1 — Remote study with guided digital material

This section covers how the removal of contaminated soil is organised and how oil behaves in different soil types, which together determine how contaminated land is cleaned up.

LESSON 1

Organising the removal of contaminated soil

An oil-spill response plan should have an appendix listing, with contact details, excavator and earth-moving companies used by the rescue department, as well as the licensed receivers/receiving sites for contaminated soil.

The following points should be noted:

  • how and by whom the clean-up is carried out
  • who organises transport, taking permits and consignment notes into account
  • the receiving site for contaminated soil
  • sampling
  • cooperation with the authorities

LESSON 2

Points to note in further clean-up

Further clean-up work also involves specific organisational responsibilities.

  • the regional environment centre is responsible, where necessary, for organising further measures
  • the party causing the damage, the responsible party, must be given the opportunity to take part in the further clean-up

LESSON 3

How oil behaves in different soil types

The behaviour of oil in soil is affected by the properties of the oil, the conditions of the soil (both natural and constructed), and the movement of groundwater.

Points to note on the absorption of oil into soil:

  • light oil products soak quickly into highly water-permeable soil, such as sand and gravel, within hours or sometimes only minutes
  • oil sinks downward until it meets groundwater, or impermeable soil before that
  • in the soil, oil spreads parallel to the groundwater or the impermeable surface, forming a roughly circular area saturated with oil
  • because light oil products are lighter than water, oiling forms mainly in the capillary zone above the groundwater surface
  • the thickness of the capillary zone is 5–10 cm in gravel and 1–2 metres in silt

LESSON 4

Petrol

Petrol penetrates sandy soil 2–10 times faster than water, meaning that response measures must begin urgently in coarse-grained soils. Its solubility in water varies with composition; MTBE is the most soluble in soil or water and, once released, evaporates mainly into the air, although evaporation slows considerably in cold conditions.

In soil, the different components of petrol can migrate to groundwater. The additive MTBE dissolves readily in groundwater and travels long distances. Some components of motor petrol are toxic or harmful to aquatic organisms.

LESSON 5

Light fuel oil and diesel

Oil that has entered the ground partly evaporates into the air, but the main components of the substance bind tightly to the soil material. In soil, light fuel oil breaks down under aerobic conditions, but binding of the components to the soil material hinders breakdown.

It does not migrate very easily in soil containing humus, but migration can be considerable in gravel and sandy soil. It dissolves to some extent in water and can evaporate from surface water into the air. In water, the oil breaks down slowly under aerobic conditions. It is harmful to aquatic organisms and highly bioaccumulative in them.

LESSON 6

Heavy fuel oil

When it enters soil, heavy fuel oil solidifies, after which it is largely non-volatile. It binds to the soil material and is therefore non-migratory and highly persistent.

It is almost insoluble in water, and its heaviest components sink to the bottom; its components bind to particles present in water. It breaks down slowly, and some of its constituents do not break down at all.

LESSON 7

Soil types

The following soil types are the most relevant to oil-spill behaviour on land.

LESSON 8

Till

Till is Finland's most common soil type. It was formed by direct deposition from a glacier, as basal till or surface till. It consists of unsorted material, with all grain sizes from boulders to fine material mixed together.

Its permeability to water is variable: permeability decreases as the proportion of fine material increases. Its landforms include drumlins, hummocky moraines and others.

LESSON 9

Clay and silt

Clay and silt are soil types formed by settling from standing water. They occur in low-lying and flat areas, and hardly at all in South Savo. They are poorly permeable to water.

LESSON 10

Sand and gravel

Sand and gravel are soil types deposited by flowing water. They are sorted soil types with no fine material present, and they occur in eskers and marginal formations (for example the Salpausselkä ridges). They are the best areas for groundwater formation and use: they are highly permeable to water.

Review questions

For self-study only. Answers are not recorded.

  1. 1. What must be considered in the clean-up of contaminated areas?

    Select all that apply.

  2. 2. Which factors govern the behaviour of oil in soil?

    Select all that apply.

    Answer key awaiting instructor review.

  3. 3. What must be noted about oil soaking into soil?

    Answer key awaiting instructor review.

The certificate is issued after both the practical exercise and the final exam.