Oil-spill response methods
Step 1 — Remote study with guided digital material
Oil-spill response methods across different environments: at sea, in coastal areas, inland waters and archipelagos, and on land, together with the resource-tiering model used for ship-source spills.
LESSON 1
Oil-spill response methods
The response equipment for oil that has entered the water consists of the rescue service's boat fleet, oil booms used to contain the spread of oil, oil skimmers intended for recovering oil from the water surface, and transfer pumps together with their power units.
At sea, on the open sea, responsibility for oil-spill response lies with the Border Guard. If an oil spill occurs in Finland's exclusive economic zone or in territorial waters on the open sea, the Border Guard is responsible for directing the response and appoints the rescue operation commander. If, instead, the damage occurs in a rescue service's own water area, that rescue service is responsible for directing the response and appoints the rescue operation commander.
Further sections of the course address, in more detail, oil-spill response in coastal areas, inland waters and archipelagos; in rivers and other flowing-water environments; along the shoreline; and on land areas.
LESSON 2
Ship-source oil-spill response
Statistically, an average of 14.5 vessel accidents and two ship-source oil discharges occur annually in the Gulf of Finland. The risk of an oil spill is significant. In addition to damage occurring during operational bunkering or cargo transfer, an oil leak as a result of grounding or bottom contact is quite possible. There is also a risk of a large oil cargo spill.
An international tiering model, Tiered Preparedness and Response, has been developed to support preparedness for ship-source oil spills, response planning and the definition of response resources. The aim of the model is to make it easier to prepare for oil spills of differing severity and to define what resources their response requires. Under the model, oil spills are classified into three tiers (Tier 1–3) according to the potential severity of the damage and the amount of resources required for the response.
- Oil-spill response tasks: bagging off the leak point with booms
- Slowing the spread of leaking oil with booms
- Directing the leaking oil
- Protecting specific points with booms
- Recovering the oil
- Tier 1 — a smaller oil spill for which local resources are sufficient
- Tier 2 — an oil spill requiring regional resources in addition to local ones
- Tier 3 — a major oil spill requiring national, and possibly neighbouring countries', resources
LESSON 3
Response operation for an oil spill at sea
A response operation for a major ship-source oil spill at sea is organised according to a command chart and reporting relationships, and is divided into the following areas of activity.
- 1. Rescue operations, activity on board the stricken vessel
- 2. Reconnaissance, mapping and drift/trajectory modelling
- 3. Response at sea, containment
- 4. Oil recovery at sea
- 5. Alternative response methods — dispersants, burning. Note: burning oil or using dispersants requires special consideration and an exemption permit from the Finnish Environment Institute
- 6. Protecting sensitive targets
- 7. Shoreline reconnaissance
- 8. Shoreline collection and shoreline clean-up
- 9. Animal care
- 10. Logistics
- 11. Waste management
- 12. Communications and stakeholder cooperation
- 13. Cost accounting and compensation administration
- 14. Environmental impact assessment
LESSON 4
Oil-spill response in coastal areas, inland waters and archipelagos
Response to oil that has entered the water consists of the rescue service's boat fleet, oil booms used to contain the spread of oil, recovery of oil from the water surface using suitable oil skimmers and transfer pumps together with their power units, and temporary storage of the recovered oil, either aboard oil-recovery vessels or with the help of recovery barges or floating tanks.
On land and along the coastline, booming can be used to assist mechanical oil skimmers. It should be noted that when oil mixes into ground material such as beach sand, soil, mud and vegetation, this considerably increases the workload of the response effort, the amount of contaminated waste, and the cost of the response work.
The following sections cover in more detail the various response methods and equipment technology.
- Booming
- Skimmers
- Power units
- Transfer pumps
- Boat fleet
- Absorbent materials
- Maintenance, storage and upkeep
LESSON 5
Oil-spill response on land areas
Oil spilled on poorly permeable ground, such as clay soil, which cannot absorb significantly into the ground, is collected in depressions, ditches, water pools or excavated basins, from which it can then be removed, for example, by suction with vacuum trucks.
Where the ground is highly permeable, such as sand or gravel, the flow of oil should be directed into ditches or pits containing water, since oil, generally being lighter than water, will remain on the water surface. Water can also be pumped into dry ditches or oil-collection depressions to form a cushion beneath the oil that prevents it from soaking further in. The flow of oil can also be directed outside the permeable area to be dammed, or led into depressions lined, for example, with plastic sheeting. Where groundwater is close to the surface in permeable ground, it is often worth excavating and removing the oiled soil already as part of the immediate response measures.
The first action in an accident situation should be to establish what hazardous substances are involved. This is identified, for example, from placards and the consignment note, or from dispatch information obtained from the oil loading site on what substances were loaded onto the vehicle, if consignment notes or a fill indicator cannot be found. It is important to establish and prevent the risk of explosion, for example by measuring the size of the leak, taking account of location and weather conditions. More detailed operating instructions and information on chemicals can be obtained, for example, from the UN book, eTokeva, the OVA guidelines, or an international chemical register. The surroundings of the accident site are surveyed in terms of groundwater, watercourses and soil, and an assessment is made of any groundwater protection needed and of other risk targets such as ditches, drains, wells, water intakes and any Natura areas. Other normal measures should also be remembered, such as taking account of nearby residents, for example in the case of a petrol leak (fire, gases, etc.).
Isolating the accident site involves: isolating the area with warning tape, traffic signs and warning signs and similar; use of foam, protective mist and similar; maintenance and rinsing/washing facilities for protective equipment; arranging traffic control together with the police and road authorities, and issuing authority and media bulletins; and putting into use protective equipment suited to the task, since anyone working with oil products during the accident is protected with appropriate gear. Clothing that has come into contact with fuel cannot be safely reused in rescue duties, even after washing.
Plugging leaks and preventing the spread of oil requires tools such as wedges, containers, absorbent material, cloth and a lifting cushion, and an oil-recovery boom log. A situation analysis is carried out to confirm the response equipment needed and available, and to call in the cooperation network on site or inform them of the situation as necessary. A description of the roles and responsibilities of the different parties should be found in the rescue service's oil-spill response plan — for example for sampling: the initial samples that may be taken by the rescue service, the follow-up measures of the local environmental authority, and the point at which the work passes to an outside expert.
- Tank emptying — points to note: do not begin emptying if you do not know what you are doing
- Ensure the tank's protective earthing throughout every emptying method
- Consider the drop height of the liquid (e.g. petrol) and its effect on increased static build-up
- An apparently non-leaking tank can start leaking once it receives air from outside; this can happen when opening the bottom valve or, for example, when drilling an opening
- Emptying the tank via the vapour-recovery system with the tank the right way up, i.e. the tanker resting on its wheels
- Emptying via the bottom valve with the tank upside down
- Emptying via the manhole cover; this can only be done after the vapour-recovery line has been emptied
- Making an opening and emptying the tank through it; pay particular attention to occupational safety when undertaking this — making an opening (a hole) is always the last resort
Review questions
For self-study only. Answers are not recorded.
1. What is not part of the main response equipment for oil that has entered the water?
2. Which of the following statements is correct?
3. How can you identify what substances have been loaded onto a vehicle?
Select all that apply.
Answer key awaiting instructor review.
4. Where should oil that has spilled onto poorly permeable (clay) ground be collected?
Select all that apply.
Answer key awaiting instructor review.
Mechanical response module in the demo
The certificate is issued after both the practical exercise and the final exam.